Truck Crane Machine Use 232.20.0500.503 Type 21/650.2 648x445.2x56mm Slewing Ball Bearing

Truck Crane Machine Use 232.20.0500.503 Type 21/650.2 648x445.2x56mm Slewing Ball Bearing

 
  232.20.0500.503 Single row four-point contact ball slewing bearings
232.20.0500.503 Slewing bearing without teeth ,648x445.2x56mm, JBT10471 quality Standard
Dimensions - d (inside diameter) 445.2 mm
Dimensions - D (outside diameter) 648 mm Dimensions - H (Height) 56 mm

 Forging process:
The blanks of bearing rings are mainly made of rods and tubes, while the forging process is only applicable to rods. However, forgings are the most used blank materials in bearing manufacturing, and are suitable for large and medium-sized bearings. Forging can be divided into hot forging, cold forging and warm forging. Hot forging refers to processing above the re-crystallization temperature of the billet metal, warm forging is forging at a temperature not exceeding the re-crystallization temperature, and cold forging refers to forging at normal temperature.
 
Heat treatment
3.1 Raceway surface quenching: The bearing raceway surface is quenched at medium frequency, the hardness is not less than 55HRC, the depth of the hardened layer is not less than 4mm, the width of the soft belt is less than 50mm, and the "S" mark is marked accordingly. (Sometimes customers can request carburizing, nitriding, carbonitriding, etc.)
3.2 Tempering after heat treatment: After the intermediate frequency quenching of the inner and outer rings of the bearing, it is required to be exposed to 200C degrees for 48 hours before being baked. To ensure that internal stresses disappear.
Rolling and milling processing—4.1 For turntable bearings with internal and external teeth, the grinding and milling teeth must be carried out before the grinding process, and they must be processed in strict accordance with the technological requirements, with an accuracy level of 8 or more.
5) Drilling—
5.1 Scribing: After measuring the external dimensions of the part, carry out the scribing and positioning procedures according to the dimensions specified in the drawing. The holes should not differ from each other by more than 3%.
5.2 Drilling: Check the scribe line size according to the drawing, and then perform the drilling process after ensuring that the dimensions are correct. The inner sleeve turntable bearing mounting holes should be combined and processed, and the error between the holes at 180C degrees between the soft belts should not be greater than 5%.
06) Grinding
6.1 Coarse grinding: Use medium corundum and soft three-grained granularity of 36 degrees and atmospheric hole resin grinding wheels for grinding. The line speed is controlled at 1500 rpm to prevent raceway burns. The maximum grinding depth must not exceed 1 mm.
6.2 Fine grinding: Use resin wheel grinding with a granularity of 46 degrees or 60 degrees, the grinding amount should be less than that of rough grinding, and the finish must reach the level specified in the drawing

Generally, only the raceways in the rings are hardened and precision- ground. Integral seals  made of acrylonitrile- butadiene rubber (NBR) keep the lubricant in, and contaminants out of the bearing.
232.20.0500.503 Slewing bearings perform extremely well in a variety of applications such as:
• bucket wheel excavators
• conveyor booms
• cranes of all types
• small, medium and large excavators
• indexing tables
• ladle turrets
• offshore applications
• robots
• railway bogies
• rotary platforms
• stackers
• solar mirrors
• tunnel boring machines
• wind turbines
 
 

How to choosing the right bearing size and type:
First:Please check the loads,axial load and radial loads
Second:The percentages of collective load with respective time
Third:Speed or number of movements ,that is the angle rotated within the time unit
Fourth:Circumferential forces transmitted by the gear
Fifth:Bearing boundary
Sixth:such as the bearing working temperature

Outer ring and inner ring material
42CrMo and 50Mn are used for slewing bearing with surface quenching treatment of the raceway.Other kinds of surface quenched steel can also be used according to customer specification and operating conditions
Rolling Material:
The Rolling elements is ball or roller, All the ball or roller will use LYC Brand.The material of rolling elements in bearing is GCr15 or GCr15SiMn

Slewing bearing is one of our main products.
1. four point contact ball slewing bearing (no gear, external gear, internal gear);
2. two row ball slewing bearing (no gear, external gear, internal gear);
3. crossed cylindrical roller slewing bearing;(no gear, external gear, internal gear);
4. three row cylindrical roller slewing bearing;(no gear, external gear, internal gear);
5. crossed tapered roller slewing bearing; (no gear, external gear, internal gear);
6. ball and roller combined slewing bearing.(no gear, external gear, internal gear);

JHB slewing ring bearings can be packed by different ways.
If bearing diameter is less than 2300mm, slewing rings will be usually packed by square plywood case.
If bearing diameter is more than 2300mm, slewing rings can be packed by square plywood case, round plywood case, or steel tripod. Every package way can be totally kept goods safely.

5. JHB Slewing Bearing Transportation:
Slewing bearings can be offered different delivery terms, such as EXW, FOB, CIF, DDU and so on.
Also, slewing rings can be transported by different transport ways, by express (such as DHL, TNT, UPS, FEDEX and so on), by air, by sea, by truck, by railway and so on.